Additional Information
50% stronger than standard hook & loop fasteners, Sticks to most surfaces, including plastic, Excellent for indoor or outdoor use Shape: Strips Care and Application: Instructions: Clean and dry surface before application, Peel tape from fastener and press firmly into place, Adhesive reaches maximum strength after 24 hours Note: Recommended for temperatures between 0°F to 120°F. Not recommended for fabrics, dashboards, flexible vinyl or underwater use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 10 lbs Functional Temperature Range: 0-120° F (-18-49° C) 1 Compatible with Genuine Joe Hand Towel Dispenser 2 Indoor / outdoor use, Superior adhesive for most surfaces, 50% stronger than standard hook and loop fasteners Shape: Strips Care and Application: Instructions: Clean and dry surface before application, Peel tape from fastener and press firmly into place, Adhesive reaches maximum strength after 24 hours Note: Recommended for temperatures between 0°F to 120°F. Not recommended for fabrics, dashboards, flexible vinyl or underwater use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 10 lbs Functional Temperature Range: 0-120° F (-18-49° C) 1 Shape: Roll Care and Application: Instructions: Clean and dry surface before application, Peel tape from fastener and press firmly into place, Adhesive reaches maximum strength after 24 hours Note: Not recommended for fabrics, dashboards, flexible vinyl or underwater use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 10 lbs Functional Temperature Range: 0-120° F (-18-49° C) 1 Shape: Roll Care and Application: Instructions: Clean and dry surface before application, Peel tape from fastener and press firmly into place, Adhesive reaches maximum strength after 24 hours Note: Recommended for temperatures between 0°F to 120°F. Not recommended for fabrics, dashboards, flexible vinyl or underwater use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 10 lbs Functional Temperature Range: 0-120° F (-18-49° C) 2
