Hanging2 Home2 Mounting2 Office4 School2 Wood3 Glass1 Plastic1 Poster1 Smooth Surface1 Tile1

0.62"1 0.63"3 0.75"3

Hook & Loop Fastener10 Sticky Tape10

0.59"1 0.62"1 0.75"9 0.87"2

0.59"1 0.62"1 0.87"2 5 ft3 10 yd2 15 ft3 16.67 yd1

Carton2 Roll4

Adhesive2 Hook & Loop Fastener3 Long Lasting2 Peel-off5 Precut4 Strong2 Durable1 Peel & Stick1

Beige2 Black7 Clear3 White8

Beige2 Black7 Clear3 White8

Blends into surfaces for inconspicuous look, No need to match fastener color to décor or project Shape: Circles Care and Application: Instructions: Clean and dry surface before application, Peel tape from fastener and press firmly into place, Adhesive reaches maximum strength after 24 hours Note: Not recommended for fabrics, dashboards, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)1 Easy to use, For smooth surfaces, General purpose fasteners for everyday use, Adhesive reaches maximum strength after 24 hours Shape: Circles Care and Application: Instructions: Clean and dry surface before application., Peel tape from fastener and press firmly into place., Adhesive reaches maximum strength after 24 hours. Note: Not recommended for fabrics, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)2 Shape: Circles Care and Application: Instructions: Clean and dry surface before application., Peel tape from fastener and press firmly into place., Adhesive reaches maximum strength after 24 hours. Note: Not recommended for fabrics, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)3 Shape: Circles Care and Application:Instructions: Clean and dry surface before application., Peel tape from fastener and press firmly into place., Adhesive reaches maximum strength after 24 hours. Note: Not recommended for fabrics, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating:1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)1 Shape: Circles Care and Application: Instructions: Clean and dry surface before application., Peel tape from fastener and press firmly into place., Adhesive reaches maximum strength after 24 hours. Note: Not recommended for fabrics, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)1 Shape: Roll Care and Application: Instructions: Clean and dry surface before application., Peel tape from fastener and press firmly into place., Adhesive reaches maximum strength after 24 hours. Note: Not recommended for fabrics, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)6 Shape: Roll Care and Application: Instructions: Clean and dry surface before application, Peel tape from fastener and press firmly into place, Adhesive reaches maximum strength after 24 hours Note: Not recommended for fabrics, dashboards, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)1 Shape: Roll Care and Application: Instructions: Clean and dry surface before application., Peel tape from fastener and press firmly into place., Adhesive reaches maximum strength after 24 hours. Note: Not recommended for fabrics, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating:1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)1 Shape: Squares Care and Application: Instructions: Clean and dry surface before application, Peel tape from fastener and press firmly into place, Adhesive reaches maximum strength after 24 hours Note: Not recommended for fabrics, dashboards, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)1 Shape: Squares Care and Application: Instructions: Clean and dry surface before application., Peel tape from fastener and press firmly into place., Adhesive reaches maximum strength after 24 hours. Note: Not recommended for fabrics, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)1 Shape: Squares Care and Application:Instructions: Clean and dry surface before application., Peel tape from fastener and press firmly into place., Adhesive reaches maximum strength after 24 hours. Note: Not recommended for fabrics, flexible vinyl or outdoor use. Continued exposure to full sunlight can damage fastener. Removal Instructions: Warm the tape (Hook or Loop) with a hair dryer. (Do not use a heat gun), Peel off the tape (Hook or Loop) the adhesive will remain on the substrate, Warm the adhesive with the hair dryer (again, do not use a heat gun), peel off a piece and roll in a ball, Cool the adhesive down. This may be done with ice in a plastic bag (only takes a few moments), Stick the ball on the adhesive which is on your substrate and pull it off, Repeat step # 5 until the adhesive is completely removed from the substrate. This may take some time, If any residue tackiness remains on the substrate you may now use a commercial remover like Goo Gone, acetone, WD-40, mineral spirits or citrus based cleaners Weight Rating: 1 lbs per square inch up to 5 lbs Functional Temperature Range: 0-100° F (-18-38° C)1

Mexico16 United States4